diff options
Diffstat (limited to 'source/n/network-scripts/scripts/rc.inet1.conf')
| -rw-r--r-- | source/n/network-scripts/scripts/rc.inet1.conf | 107 |
1 files changed, 107 insertions, 0 deletions
diff --git a/source/n/network-scripts/scripts/rc.inet1.conf b/source/n/network-scripts/scripts/rc.inet1.conf new file mode 100644 index 00000000..555210c4 --- /dev/null +++ b/source/n/network-scripts/scripts/rc.inet1.conf @@ -0,0 +1,107 @@ +# /etc/rc.d/rc.inet1.conf +# +# This file contains the configuration settings for network interfaces. +# If USE_DHCP[interface] is set to "yes", this overrides any other settings. +# If you don't have an interface, leave the settings null (""). + +# You can configure network interfaces other than eth0,eth1... by setting +# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset +# or empty, it is assumed you're configuring eth<interface>. + +# Several other parameters are available, the end of this file contains a +# comprehensive set of examples. + +# ============================================================================= + +# Config information for eth0: +IPADDR[0]="" +NETMASK[0]="" +USE_DHCP[0]="" +DHCP_HOSTNAME[0]="" + +# Config information for eth1: +IPADDR[1]="" +NETMASK[1]="" +USE_DHCP[1]="" +DHCP_HOSTNAME[1]="" + +# Config information for eth2: +IPADDR[2]="" +NETMASK[2]="" +USE_DHCP[2]="" +DHCP_HOSTNAME[2]="" + +# Config information for eth3: +IPADDR[3]="" +NETMASK[3]="" +USE_DHCP[3]="" +DHCP_HOSTNAME[3]="" + +# Default gateway IP address: +GATEWAY="" + +# Change this to "yes" for debugging output to stdout. Unfortunately, +# /sbin/hotplug seems to disable stdout so you'll only see debugging output +# when rc.inet1 is called directly. +DEBUG_ETH_UP="no" + +## Example config information for wlan0. Uncomment the lines you need and fill +## in your data. (You may not need all of these for your wireless network) +#IFNAME[4]="wlan0" +#IPADDR[4]="" +#NETMASK[4]="" +#USE_DHCP[4]="yes" +#DHCP_HOSTNAME[4]="icculus-wireless" +#DHCP_KEEPRESOLV[4]="yes" +#DHCP_KEEPNTP[4]="yes" +#DHCP_KEEPGW[4]="yes" +#DHCP_IPADDR[4]="" +#WLAN_ESSID[4]=DARKSTAR +#WLAN_MODE[4]=Managed +#WLAN_RATE[4]="54M auto" +#WLAN_CHANNEL[4]="auto" +#WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2" +#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16" +#WLAN_WPA[4]="wpa_supplicant" +#WLAN_WPADRIVER[4]="wext" +#WLAN_WPAWAIT[4]=30 + +## Some examples of additional network parameters that you can use. +## Config information for wlan0: +#IFNAME[4]="wlan0" # Use a different interface name instead of + # the default 'eth4' +#IFNAME[4]="eth0:1" # Set up an IP alias. +#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address +#MTU[4]="" # The default MTU is 1500, but you might need + # 1360 when you use NAT'ed IPSec traffic. +#DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client to + # wait for server resonse is 10 seconds, but + # you might want a shorter or longer wait. +#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten +#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten +#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change + # your default gateway +#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP + # server +#DHCP_DEBUG[4]="yes" # Make dhcpcd show verbose diagnostics +#DHCP_NOIPV4LL[4]="yes" # Do not assign an ipv4ll address when a DHCP + # server is not found (ipv4ll link-local + # adresses in the IP range 169.254.0.0/16 are + # also known as "zeroconf" addresses) +#WLAN_ESSID[4]=DARKSTAR # An example of how you can override _any_ + # parameter defined in rc.wireless.conf, by + # prepending 'WLAN_' to the parameter's name. + # Useful with multiple wireless interfaces. +#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey" + # Some drivers require a private ioctl to be + # set through the iwpriv command. If more than + # one is required, you can place them in the + # IWPRIV parameter (separated with the pipe (|) + # character, see the example). +#WLAN_WPA[4]="wpa_supplicant" # Run wpa_supplicant for WPA support +#WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the + # ndiswrapper driver (if you leave this empty + # the 'wext' driver is used by default) +#WLAN_WPAWAIT[4]=30 # In case it takes long for the WPA association + # to finish, you can increase the wait time + # (defaults to 10 seconds) |